IPC64/19 MS-DOS STARTER KIT - CABLE
The IPC64/19 is a open frame industrial PC system. The backside (behind the 34- key front panel keyboard and the 6.5" Color VGA TFT LCD) consists of the BB2 Base Board and a PC/104 Single Board Computer (SBC). In the IPC64/19 MS-DOS Starter Kit, the CP/486DX1 is the PC/104 SBC. In some configurations the 2.5" hard disk drive (Option) is mounted direct over the PC/104 SBC. The next picture shows more details (without 2.5" hard disk drive option).

The IPC64/19 MS-DOS Starter Kit comes with some cables and other parts. Before using the IPC64/19 MS-DOS Starter Kit, it is necessary to connect the following cables to the BB2 Base Board and the CP/486DX1 Single Board Computer (SBC). Please note: Before installing the cables, touch a metal case (i.e. the metal case of your desktop computer) with your hand to reduce any static electricity that might have build up while handling the IPC64/19.

  • 1 * Power Cable with 7-pin female DIN Connector (BB2 Base Board)
  • 1 * Keyboard I/F Cable with 5-pin female DIN Connector (BB2 Base Board)
  • 1 * Cable with a RESET Switch (BB2 Base Board)
  • 1 * SBC COM Port I/F Cable with 9-pin male SUB-D Connector (SBC - COM1)
  • 1 * SBC COM Port I/F Cable with 9-pin male SUB-D Connector (SBC - COM2)
  • 1 * SBC LPT Port I/F Cable with 25-pin female SUB-D Connector (SBC LPT)

Power is brought into the IPC64/19 through a 7-pin power connector on the BB2 Base Board. Please connect the starter kit power cable to the 7- pin power connector of the BB2 Base Board. For using a external PC keyboard together with the IPC64/19, the BB2 Base Board offers a 5- pin keyboard connector. Please connect the starter kit keyboard interface (I/F) cable with this connector. The keyboard I/F cable and the power cable are very similar. Please note the differences. The power cable offers a 7- pin female DIN connector on one end, the keyboard I/F cable only a 5- pin female DIN Connector. In addition to the power and keyboard I/F cable, the IPC64/19 MS-DOS Starter Kit offers a cable with a RESET switch on one end. Connect this cable to the 2- pin RESET connector of the BB2 Base Board.

The IPC64/19 MS-DOS Starter Kit comes with three cables for the CP/486DX1 PC/104 single board computer (SBC). One 26- pin ribbon cable is for the CP/486DX1 LPT port. The parallel signals of the CP/486DX1 LPT port are wired to a 26- pin connector. The starter kit LPT Port I/F Cable with 25- pin female SUB-D Connector convert the 26- pin connector pinout to a standard PC LPT port pinout. Please connect this cable to the CP/486DX1 LPT port.

The two 10-pin ribbon cables of the IPC64/19 MS-DOS Starter Kit are for the CP/486DX1 COM ports COM1 and COM2. The COM port signals of the CP/486DX1 are wired to two 10- pin connectors. The starter COM Port I/F Cables with the 9- pin male SUB-D Connectors convert the 10- pin connector pinout to a standard PC COM port pinout.

COM1 / COM2 Pinout on the 9-pin SUB-D Connector
Pin Name Function Direction
1 DCD Data Carrier Detect IN
2 RxD Receive Data IN
3 TxD Transmit Data OUT
4 DTR Data Terminal Ready OUT
5 GND Signal Ground ---
6 DSR Data Set Ready IN
7 RTS Request to Send OUT
8 CTS Clear to Send IN
9 RI Ring Indicator IN

LPT Pinout on the 25-pin SUB-D Connector
Pin Function Direction
1 Strobe I/O
2 Data Bit 0 I/O
3 Data Bit 1 I/O
4 Data Bit 2 I/O
5 Data Bit 3 I/O
6 Data Bit 4 I/O
7 Data Bit 5 I/O
8 Data Bit 6 I/O
9 Data Bit 7 I/O
10 Acknowledge IN
11 Busy IN
12 Paper End IN
13 Select IN
14 Autofeed OUT
15 Error IN
16 Init. Printer OUT
17 Select Input OUT
18 - 25 Signal Ground ---

| Home Page | IPC64/19 |
SSV SOFTWARE SYSTEMS PC/104 Products. IPC64/19 FPPC SK. File: P134.HTM, Last Update: 17-Jul-1998
Copyright (c) 1996 - 1998 WST. All rights reserved.